MCT8315A: Reserved bit of TRAP_CONFIG1 must be set to 1
Part Number: MCT8315ATool/software:Hi,I use a MTC8315AIV on a custom board and I have a strange behavior when I configure EEPROM register TRAP_CONFIG1 .According to the datasheed the bit 19 of...
View ArticleDRV8251: Retry While Using the Demo Board
Part Number: DRV8251Tool/software:Hello,We are using the DRV8251EVM to test a motor. When I lock the motor, I trigger the OCP but the chip goes into retry mode. As far as I know, the board has the...
View ArticleDRV8243-Q1: Recommendations for ASIL-C coverage with DRV8243
Part Number: DRV8243-Q1Tool/software:Hi,Does TI have any recommendations for achieving the ASIL-C coverage with DRV8243-Q1 full-bridge driver?
View ArticleMCF8316AEVM: 3D CAD Model
Part Number: MCF8316AEVMTool/software:Is there a 3D CAD model available for this eval kit? The design files appear to contain a PDF with some views of one, but I was unable to find a STEP or similar...
View ArticleDRV8353: MOSFET connected in parallel
Part Number: DRV8353Tool/software:Hello Team,Customer would like to drive 2 or 3 MOSFETs connected in parallel with DRV8353. Is there any design recommendation? Or any related article you can share....
View ArticleMCT8329EVM: VREG_EXT_FET
Part Number: MCT8329EVMTool/software:If I change the jumper from position 1-2 to position 5-6 in J12, after sometime the I2C is automatically disabling but no faults from driver or controller.
View ArticleClik here to view.
DRV8353: Bias Voltage
Part Number: DRV8353Tool/software:In the conditions of the VSP=VSN=0V, VREF_DIV = 1b, what're the VBIAS values in min and max?RegardsBrian
View ArticleDRV3256-Q1: Cleat Fault
Part Number: DRV3256-Q1Tool/software:Hi.In DRV3256A, we are trying to reset the fault from Clear fault bit IC_CTRL_1 --> CLR_FLT--> 1b1. we tried multiple times, but fault persists, let us know...
View ArticleClik here to view.
DRV8300DPW-Q1EVM: DRV8300DPW-Q1EVM: Hall sensor noise reduction
Part Number: DRV8300DPW-Q1EVMOther Parts Discussed in Thread: LAUNCHXL-F28069MTool/software:Hi, 1. We have used TI launch pad boards (LAUNCHXL-F28069M) for the model based development and tested our...
View ArticleClik here to view.
DRV8251A: Output Voltage Problem
Part Number: DRV8251ATool/software:Hi Sir,Have Problem of Drv8251a Output Voltage,Yellow and Green Line was PWM Output,Not a normal square wave,It's normal?
View ArticleDRV3901-Q1: EVM Schematic and layout file
Part Number: DRV3901-Q1Tool/software:HiCould you help provide DRV3901-Q1 EVM schematic and layout files ? I had download EVM user guide, but there is no related information....
View ArticleClik here to view.
MCT8316Z-Q1: nFAULT indication due to NPOR bit
Part Number: MCT8316Z-Q1Tool/software:hi,i am using MCT8316 with SPI interface on a custom boardafter power up nFAULT is pulled low.when reading internal registers, NPOR bit is indicated as fault (bit...
View ArticleClik here to view.
MCF8315EVM: The motor will not turn and the motor drive wires never get...
Part Number: MCF8315EVMTool/software:I have this EVM board running at 24V connected to a maxon motor.When I power it up I cant get the motor to turn it is as if the system has a fault.The gate driver...
View ArticleDRV8214: Inquiry on Real-time Parameter Readout via I2C and Internal ADC Specs
Part Number: DRV8214Tool/software:Hello TI Support Team,I’m working with the DRV8214 and have a few questions about motor performance parameters that I couldn’t find in the datasheet. Specifically:Is...
View ArticleClik here to view.
DRV8870: DRV8870 reverse current protection and Ivm value
Part Number: DRV8870Tool/software:Hi TeamI have two question about DRV8870.1. do H bridge need a reverse current protection? or it default need a reverse current so VM need to handle reverse current?2....
View ArticleDRV8242S-Q1EVM: How to stop motor using external GPIO commands?
Part Number: DRV8242S-Q1EVMOther Parts Discussed in Thread: MSPM0G3507Tool/software:I'm looking to validate a motor control algorithm programmed on an MSPM0G3507 and I'm using a DRV8242 EVM to test it...
View ArticleDRV8215: tTURNOFF for nSLEEP
Part Number: DRV8215Tool/software:Team,DRV8215 datasheet mentions on page 33:7.4.2 Low-Power Sleep Mode When the nSLEEP pin is low for tTURNOFF time, the DRV8215 enters a low-power sleep mode. In sleep...
View ArticleDRV8213: device to replace G2015
Part Number: DRV8213Tool/software:Hi Sir, We want to find a solution to replace GMT G2015 (constant current type 1-ch H-bridge driver IC) and we suggest DRV8213. Customer think it's too complex. Do we...
View ArticleMCF8329A: SPEED-FDBK register related issues
Part Number: MCF8329ATool/software:SPEED-FDBK register offset 76EhQuestion: When it is OUTA-OUTC-OUTB, does the faster the speed, the smaller the value of this register for negative numbers. For...
View ArticleDRV3245E-Q1: Drive certified for IEC 60601
Part Number: DRV3245E-Q1Tool/software:Hello,Our company developing a robotic manipulator for bronchoscopy procedure. Our regulation consultant guided us to use motor drive certified for IEC60601.Do TI...
View Article