MCF8329A: I2C Read Write operation
Part Number: MCF8329ATool/software:"Hello,I have a few questions.Currently, I am controlling the motor using I2C. I understand that if I input values into the shadow register, they are written to the...
View ArticleDRV8242-Q1: Can't clear nFAULT
Part Number: DRV8242-Q1Tool/software:I’m having trouble getting the DRV8242S-Q1 to work. After power-on and I set nSLEEP high, nFAULT goes low. Then I send the CLR_FLT command (0x80 to register 0x08),...
View ArticleDRV8329-Q1: 3D files - for thermal simulation
Part Number: DRV8329-Q1Tool/software:HiMy costumer is asking for 3D files of the DRV8329-Q1 for thermal simulation.They would need STEP files for modelling the component, but similar 3D files will also...
View ArticleMCT8315Z: Changing direction causes fault (probably motor lock fault)
Part Number: MCT8315ZTool/software:Hello!We have tested the evaluation board with a BLDC motor from Maxon (283828) connected to two different planetary gears (1:29 and 1:84 reduction). We want to...
View ArticleDRV8952: Designing with DRV8952
Part Number: DRV8952Tool/software:Hello Team,We have a system that uses the motor driver DRV8952DDWR.OUT1 & OUT2 forms and H Bridge and OUT3 & OUT4 forms the second H Bridge.We are using 2*24V...
View ArticleDRV8706-Q1: Current sense pin if left unconnected
Part Number: DRV8706-Q1Tool/software:Hi,For the driver DRV8706SQRHBRQ1 if I am not using the current sense pins (SP SN and SO), will this effect in any way my normal operation of driver?Regards,Reshma
View ArticleULC1001-DRV290XEVM: where to order LCS-FL-RNG15
Part Number: ULC1001-DRV290XEVMTool/software:Hi,customer wants to order LCS-FL-RNG15.it does not show up on ti.com. Where can customer place an order for it?BR,Stefan
View ArticleDRV8350: Regarding Fault Response Table(8.3.6.9)
Part Number: DRV8350Tool/software:Dear Ti.I have a question regarding Fault Response Table (8.3.6.9) in datasheet (I'm using "DRV8350RH")By looking at the attached capture image below, I interpreted...
View ArticleDRV3901-Q1: Maximum voltage for 3.4A/0.5ms deployment
Part Number: DRV3901-Q1Tool/software:Dear Sir, Madam,Could you tell me if it is possible to activate a pyrofuse at 3.4A for 0.5ms at an operating voltage PVDD = 28V?The numbers given in the datasheet...
View ArticleDRV3901-Q1EVM: DRV3901-Q1EVM flashing red fault LEDS
Part Number: DRV3901-Q1EVMTool/software:I received the eval board and have had an issue trying to bring it up. The packaging was not original as it was clear the static bag had been opened and used....
View ArticleDRV3946-Q1: RθJA in datasheet is given at which conditions ?
Part Number: DRV3946-Q1Tool/software:I would like to know at which conditions the provided value for Junction-to-ambient thermal resistance is calculated or measured ? thank you RegardsRachid
View ArticleDRV8343-Q1: Passive OLD in independent MOSFET Mode
Part Number: DRV8343-Q1Tool/software:Hi expert,My customer doesn't want the internal dead time so they plan to use independent MOSFET mode to driver 6 MOSFET.In this mode, they found the passive OLD...
View ArticleMCT8316A: Maximum continuous current
Part Number: MCT8316ATool/software:Hello,We are interested in an application for MCT8316A/MFC8316 but we are unsure on the maximum continuous current that the chip can handle. The datasheet says 8A...
View ArticleULC1001-DRV2911EVM: ULC1001-DRV2911EVM
Part Number: ULC1001-DRV2911EVMOther Parts Discussed in Thread: MSP430FR5994, DRV2911, ULC1001Tool/software:Hello,I am contacting you regarding your device: the ULC1001-DRV2911EVM evaluation module. We...
View ArticleMCF8329EVM: Startup-video link
Part Number: MCF8329EVMTool/software:Eric ChenYou sent a drive link to one of the e2e users to get the MCF 8329EVm out of the MPET tool."">e2e.ti.com/.../mcf8329evm-mpet-not-working"Can you please...
View ArticleDRV8962-Q1: 3x H-bridge operation
Part Number: DRV8962-Q1Other Parts Discussed in Thread: DRV8962, DRV8718-Q1, DRV8263-Q1Tool/software:Dear team,Can DRV8962-Q1 be used with this configuration? We like to control 3 BDC motor with 1x of...
View ArticleMCF8316AEVM: How to make sure write to EEPROM is successful or failed?
Part Number: MCF8316AEVMOther Parts Discussed in Thread: MOTORSTUDIO,Tool/software:The question is about MCF8316AEVM and Motorstudio, it drives the motor operating successfully and generated the...
View ArticleDRV8452: Setup DRV8452 via SPI for Stepper mit NEMA24 and 88mm Length (12mH,...
Part Number: DRV8452Tool/software:Hi..I have a new board with 3 DRV8452 connected via SPI. "Smaller motors" are working fine but we have a NEMA24 which should run with 300rpm. But it is getting noisy...
View ArticleDRV8311: Application issues.
Part Number: DRV8311Tool/software:Hi Team,Using DRV8311P.Using the tSPI protocol for register reading and writing, it was found that the written data is inconsistent with the read data1) NSLEEP pull...
View ArticleMCF8329EVM: Parameter setting
Part Number: MCF8329EVMTool/software:Hi,I am trying for my life to tune the multiverse of EEPROM settings for my motor using your evm, but I have no luck at all. It seems from my perspective that this...
View Article