DRV8210: The MD solution in IPC
Part Number: DRV8210Other Parts Discussed in Thread: ULN2003A,Tool/software:Hi BU expert,In IP camera, I have noticed that some customer use motor drive and some customer use Darlington. Why there is...
View ArticleDRV8434S: Multiple drivers, enable to select?
Part Number: DRV8434STool/software:Hi team,If using multiple DRV8434S drivers (A, B, C) can I use only one STEP and one DIR signal for all the drivers (A, B, and C), using the ENABLE signal to select...
View ArticleDRV8316: SPI Fault Reporting
Part Number: DRV8316Tool/software:Hello,I am verifying fault handling functionality and would like to trigger a SPI fault. I have tried creating address and parity faults using the below...
View ArticleClik here to view.
DRV8316-Q1: DRV8316-Q1
Part Number: DRV8316-Q1Tool/software:Hello ExpertWhen I was configuring register 4, I saw OCP_CBC and there was no introduction about it in the datasheet.Can you clarify the functionality of this...
View ArticleClik here to view.
MCF8329A: Cannot get motor spinning on custom hardware
Part Number: MCF8329ATool/software:Hi,I am trying to get going with a motordriver based around mcf8329a. However there seems to be a few issues in my setup. I have bought and tested everything with...
View ArticleClik here to view.
DRV8353: CSA_CAL_x
Part Number: DRV8353Tool/software:Hello team,1. If there're two current shuts(CSA_CAL_B & C) used only, how to set the register bit on rest of CSA_CAL_A?2. What's recommend setting value on...
View ArticleBOOSTXL-DRV8323RS: BOOSTXL-DRV8323RS
Part Number: BOOSTXL-DRV8323RSTool/software:Title: **Issue with Unstable Current Consumption at High RPM on BLDC Motor with 393KV and 10 Pole Pairs Using SimpleFOC**Hi community,I hope you are all...
View ArticleDRV8849: Step pins connect suooprt
Part Number: DRV8849Tool/software:Hi Team,Could we connect the pin STEP1 and STEP2 with same frequency signal?Besides, do we have some suggestions to enhance MCU's GPIO frequency? Because customer uses...
View ArticleClik here to view.
[FAQ] MCF8316C-Q1: Spinning BLDC motors with Motor Studio - default JSON...
Part Number: MCF8316C-Q1Other Parts Discussed in Thread: MCF8329A, MCF8315C, MCT8316ATool/software:Motor Studio is the primary GUI to evaluate the MCx family of devices (MCF8315C, MCF8316C, MCT8315,...
View ArticleDRV8908-Q1: Is there any recommended power-off sequence for DRV8908-Q1?
Part Number: DRV8908-Q1Tool/software:Hello experts,is there any recommended power-off sequence for DRV8908-Q1?If yes, could you please let me know the detail?Thanks,Kento
View ArticleDRV8908-Q1: Can nSLEEP pin be low during PWM output in DRV8908-Q1?
Part Number: DRV8908-Q1Tool/software:Hello experts,Can nSLEEP pin be pulled to low during PWM output in DRV8908-Q1?Any concern for this?Thanks,Kento
View ArticleClik here to view.
DRV8908-Q1: Layout example pulls nFAULT pin to low, but nFAULT pin is...
Part Number: DRV8908-Q1Tool/software:Hello experts,In the datasheet of DRV8908-Q1, the layout example pulls nFAULT pin to low.However, it is recommended to be pulled up in the datasheet. Is this layout...
View ArticleDRV8343-Q1: SPI communicate no response.
Part Number: DRV8343-Q1Tool/software:Hi Teams,e2e.ti.com/.../0_5F00_DRV8343SEVM-DVDD-NO-Voltage.PPTXWe are evaluating the DRV8343 with EVM and Customer MCU. But found cannot use SPI to communicate with...
View ArticleClik here to view.
DRV8143-Q1: ITRIP Regulation causes OTP fault
Part Number: DRV8143-Q1Tool/software:Hi Team,I'm trying to use the ITRIP regulation function on the device however after reaching the trip current, the device oscillates for a brief time and then shuts...
View ArticleDRV8801EVM: GUI Download
Part Number: DRV8801EVMTool/software:Hello,When I try to download the GUI for the EVM (www.ti.com/tool/download/SLVC370) I get an error (broken link?). Is there a different link to use?
View ArticleDRV8434S: Cannot trigger OL fault
Part Number: DRV8434STool/software:I have had good success using the Stepper Driver. However, when trying to detect a disconnected motor, I am unable to latch the OL bit in the FAULT register. All...
View ArticleDRV3946-Q1EVM: Schematic request
Part Number: DRV3946-Q1EVMOther Parts Discussed in Thread: DRV3946-Q1Tool/software:Hello, I have the user manual and datasheet for the DRV3946-Q1EVM. Can I please get the schematic for the eval board?...
View ArticleMCF8329A: question about current sensing
Part Number: MCF8329ATool/software:Hello. Could you explain how the MCF8329A handles situations where the reference voltage for current sensing is not exactly 1.5V but has a slight bias?
View ArticleDRV8714-Q1: Additional Protection at gate pin
Part Number: DRV8714-Q1Tool/software:Hi,I am working with DRV8714 and DRV8706 for my motor control application. Do I need to add gate source protection clamping diode external to the driver IC from GH...
View ArticleClik here to view.
DRV8876-Q1: Software Selectable IMODE
Part Number: DRV8876-Q1Tool/software:Hello,In our design, we are using DRV8876-Q1.For the IMODE selection,IMODE selection resistors are attached.We are using 20.5k instead of 20k and we shall use...
View Article