Clik here to view.
DRV8803: parallel output configuration
Part Number: DRV8803Hi,My customer asked if the DRV8803 can be configured with paralleled output as modified diagram below for high output current up to 2A.And he want to know about the absolute...
View ArticleRE: DRV8873-Q1: DRV8873-Q1 NMOS current characteristic
Hi Oliver, Have you heard back from your customer? Is there a specific condition the customer is concerned about?
View ArticleDRV8873-Q1: DRV8873-Q1 NMOS current characteristic
Part Number: DRV8873-Q1Hello team, happy new year!My customer is curious about NMOS drain current vs temperature specification which is integrated in DRV8873-Q1.I found Rds(on) graph in the datasheet,...
View ArticleRE: DRV8332-HT: same specs chip but one PWM signal controlled like the TI...
Hey Farouk,At the moment we don't have another high temperature controller for BLDC motor control that satisfies your requirements.We are not at this time looking at other high temperature options to...
View ArticleDRV8332-HT: same specs chip but one PWM signal controlled like the TI...
Part Number: DRV8332-HTHi Team,I'd like to use the DRV8332-HT for its guaranteed 1000hours over 165°C, the drawback I face now is that I should control it with 6PWMs or 3PWMs which is complicated; I...
View ArticleRE: shunt-resistor in each phase in( Directly measurement on the phase line ).
Thank you very much Dear Sean :) your reply is fast ,and correct. Good luck!
View ArticleRE: shunt-resistor in each phase in( Directly measurement on the phase line ).
as you know FAST needs to have voltage feed back sensors as well as current ,since the ground of HV(1200v) is directly connected to vss Microcontroller ,it is not good I think, is there any way to to...
View ArticleRE: CCS/DRV8305: Problem with DRV8305
Mohammad, The EVM is different than the device datasheet because of some design considerations: 1. The EVM may use a different clocking scheme (polarity) so therefore please use it in the mode it...
View ArticleCCS/DRV8305: Problem with DRV8305
Part Number: DRV8305Tool/software: Code Composer StudioHi ,i have few question about DRV8305 and its connection with TMS28069M;1-) in datasheet has been mentioned that SPI setting should be like this:...
View ArticleRE: shunt-resistor in each phase in( Directly measurement on the phase line ).
FAST needs the voltage feedback, so you will need to find some way to provide it. You could look into something like SDFM for isolated voltage sensing, which is a typical design choice Sean
View ArticleRE: DRV8308: RPM of EVM
Garig, I apologize for the frustration. The motor model information should be included in the User's Guide. Doing a quick search on E2E, I find the following thread which also has your...
View ArticleDRV8308: RPM of EVM
Part Number: DRV8308What is the TESTED minimum and maxium rpm that I can expect to achieve with the 8308 EVM and the included BLDC motor? What frame is the motor?Thanks
View ArticleRE: shunt-resistor in each phase in( Directly measurement on the phase line ).
thanks again dear Sean :) best wishes Dave.
View Articleshunt-resistor in each phase in( Directly measurement on the phase line ).
hi every one!I am using motorware18 prog_lab3a (for ACIM).as you may know in most of IGBT packs we do not access to leg of each low-side IGBTs .(like 7MBR50SB120)I want to use Directly measurement on...
View ArticleRE: DRV8662: questions about the input and output characteristics
Hi, Jamie, We will take a look at this thread and will answer as soon as possible. Best regards, Luis Fernando Rodríguez S.
View ArticleRE: DRV8840: DRV8842 noise
Hi Ziv, Are you using the same PWM frequency for both the DRV8840 and LMD18200? How are the PWM, Dir, and Brake inputs of the LMD18200 connected? Would you please provide scope captures of the inputs...
View ArticleRE: DRV8308: IC controller not initiating commutation at start up when...
Hi Adam,Thanks for the reply. Sorry for the delay. We Found the problem, which came from the octal switch as you are using in the EVM board to make the pseudo differential hall sensors signals from...
View ArticleRE: DRV8301: DRV8301-HC-EVM Rev D_BUCKCONVERTER
Kwan, This is a Zener clamping diode which should prevent the EN_BUCK pin from seeing more than the clamp voltage of 5V if the PVDD is higher and reaches the EN_BUCK pin.
View Article