Clik here to view.
DRV8872: VM Burns during breaking the motor
Part Number: DRV8872Tool/software:Hello Team, can you please help my customer: We use the DRV8872-Q1 to control a DC motor. It was used as a replacement because the original one from infineon went...
View ArticleDRV10983-Q1: Support
Part Number: DRV10983-Q1Tool/software:Hello.We are trying to use the DRV10983-Q1 motor driver in one of our systems. Is there any C based example code for this IC?Best RegardsFrancisco
View ArticleDRV10983-Q1: Support
Part Number: DRV10983-Q1Tool/software:Hello.We are trying to use the DRV10983-Q1 motor driver in one of our systems. Is there any C based example code for this IC?Best RegardsFrancisco
View ArticleClik here to view.
DRV8825: Using DRV8825 to drive a stepper Motor. But Motor is too hot and...
Part Number: DRV8825Tool/software:The schematic is shown below:The Reset and nSleep pins are high,but the motor doesn't move , and too hot.Vref=1.22V so,the chop current is set to 1.22A the...
View ArticleClik here to view.
DRV8873-Q1: Troubleshooting Tips for DRV8873-Q1 Going Bad
Part Number: DRV8873-Q1Other Parts Discussed in Thread: DRV8873, , SN74LVC8T245-EPTool/software:Subject: Urgent Help Needed: Issues with DRV8873-Q1 H-Bridge Driver in ProjectHi Team,We are currently...
View ArticleMCF8329A: MCF8329A1IREER Basic Operation
Part Number: MCF8329ATool/software:Hi there!I have a custom PCB with a MCF8329A1IREER controller on it paired with IPB013N06NF2SATMA1 MOSFETs. Relevant control pins are connected to a micro-controller...
View ArticleDRV8434S: Driver code
Part Number: DRV8434STool/software:Hi team,Customer come to check if we get driver code for DRV8434S.Could you help check if we could offer?Thanks and Best Regards,Will
View ArticleClik here to view.
DRV8870: DRV8870 label issue
Part Number: DRV8870Tool/software:do you have new PCN for label , left is new coming goods, right is old goods, but label is different. please help check it 。
View ArticleDRV2604: I2C spec
Part Number: DRV2604Tool/software:The customer is asking to change the i2c clock to 100KHz, but we are not able to find the timing spec for 110KHz in DRV2604L's datasheet.May we know if we could...
View ArticleDRV8849: Driving a motor using a DRV8849.
Part Number: DRV8849Tool/software:Our application uses the DRV8849 driver to control motor rotation. However, we're encountering a motor noise issue during operation with a load of 0.4 Nm.Could you...
View ArticleDRV8714-Q1: Schematic Check
Part Number: DRV8714-Q1Tool/software:Dears,New Project,use DRV8714,Pls kindly help to check my schematic,thanks.e2e.ti.com/.../VCDM_5F00_TI_9F530674FE56_.pdf
View ArticleMCT8329A: High side current sensing with MCT8329A
Part Number: MCT8329ATool/software:Hello,bacause of PCB layout it would be much easier for me to have current sense resistor at high side.I don't see it in datasheet but I asume CM voltage on MCT...
View ArticleClik here to view.
DRV8873-Q1: Operation without a microcontroller
Part Number: DRV8873-Q1Tool/software:Hi,I would like to use the hardware version of the device to control a motor, but without using a microcontroller. I can see one problem with this:Since the...
View ArticleDRV3946-Q1: External devices when using low side driver with high side...
Part Number: DRV3946-Q1Other Parts Discussed in Thread: TPS1HTC30-Q1,Tool/software:Hello,I am planning to use the high side switch TPS1HTC30-Q1 with low side driver DRV3946-Q1 (the high side switch...
View ArticleClik here to view.
DRV8262EVM: Operation by LAUNCHXL-F280025C
Part Number: DRV8262EVMOther Parts Discussed in Thread: LAUNCHXL-F280025CTool/software:Hello team,My customer would like to use DRV8262EVM and try to use their algorithm for the motor operation.Q1. Is...
View ArticleDRV10983: DRV10983
Part Number: DRV10983Tool/software:Is there any reference designs are available for a 3kW BLDC motor driver?
View ArticleDRV8305: Using only GLA to GLC as gate signals
Part Number: DRV8305Tool/software:I would like to ask about the use of the DRV8305.In 6-PWM mode, is it possible to use INHx all fixed at LOW and use only INLx (using only GLA to GLC as gate signals,...
View ArticleDRV2901: Schematic and Layout Review
Part Number: DRV2901Other Parts Discussed in Thread: DRV2911, ULC1001Tool/software:Hello,I am trying to build a test board using ULC1001 and DRV2911. Please review the attached schematic and...
View ArticleDRV8243-Q1: DRV8243-Q1: SPI (P) variant voltage change issue with PWM
Part Number: DRV8243-Q1Tool/software:DRV8243-Q1: SPI (P) variant we are using.The motor driver functions normally when operated at 12 volts, but it does not function in reverse when operated at 24...
View ArticleClik here to view.
DRV8353: Review DRV8353H shcematic and layout
Part Number: DRV8353Tool/software:Hi team,Could you help review the schematic and layout? due to customer board damage.I can share you offline. thanks
View Article