Quantcast
Channel: Motor drivers forum - Recent Threads
Browsing all 21906 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

DRV8305: Some problem while driving BLDC motor using DRV8305 and MSP430G2553.

Part Number: DRV8305Hello sir,I have used DRV8305 and an MSP430G2553 controller to drive BLDC. It runs almost perfectly but at some point of time BLDC motor internally make a sound for a second and...

View Article


RE: DRV8305: DRV8305 nFAULT Low

Hi Robert, I'm glad you were able to remove the fault. For the new issue of not being able to toggle the GHC, a have a couple questions: 1.) Does replacing R1008 solve this issue? Are you sure the...

View Article


RE: DRV8301: DRV8301 PWM not working

Hi Suraj, With no MOSFETs connected, the device will go into "Current Limit Mode" when the gate signals are enabled because the VDS differential is greater than the VDS threshold set with the OC_ADJ...

View Article

RE: DRV8301: DRV8301 heats up a lot if buck is enabled

Hi Suraj, The inductor must be connected to the buck in order for it to operate correctly. I would recommend disconnecting all external loads from the VCC buck output and checking the following...

View Article

RE: Looking for driver for a Single Phase Brushless (BLDC) Motor

Hi Josh, The DRV8701 Gate driver would be a good for this application, I would recommend following the reference design suggestion that you posted. This gate driver is best suited for the current level...

View Article


Image may be NSFW.
Clik here to view.

Looking for driver for a Single Phase Brushless (BLDC) Motor

Hello all,I am a design engineer and just starting a new project. I have done some research and it seems that what I am trying to do is quite possible, but probably not the most common. I am working on...

View Article

RE: How can I terminate floating voltage of PVDD port?

Hi Nam, Sang-il, Sorry for the delay. We were not to duplicate your findings. When GVDD and VDD = 12V, the outputs were measured to be 560mV. PVDD was measured to be 330mV. PVDD is following the OUT_x...

View Article

Image may be NSFW.
Clik here to view.

How can I terminate floating voltage of PVDD port?

Hi,Even above condition, (DRV8332 in reset and PVDD off)the power indicator LED remain on in low brightness.I could observe the floating voltage (almost 2~3V) at point of arrow.How can I terminate...

View Article


RE: DRV8303: DRV8303 Flow Through Drive of High and Low Side FETs

TI,Do you have an update as to why the DRV8303 (and DRV8301) have this undesired behavior of shoot-though, caused by a narrow pulse out of the low-side gate drive output?

View Article


Image may be NSFW.
Clik here to view.

DRV8303: DRV8303 Flow Through Drive of High and Low Side FETs

Part Number: DRV8303We are using theTMS320F28069MPZT and the DRV8303 and have a problem with the GLx (lower gate output drive) spiking up when there is a transition on the GHx signal (high side gate...

View Article

RE: Full Bridge Driver for a 100 V DC motor

Hi Daniel,I will look into them.Thanks,Marc

View Article

RE: DRV8301: DRV8301 heats up a lot if buck is enabled

Hi Phil, Thank you for your answer, I'll try this and report results here. Thank you again!!

View Article

RE: DRV8301: DRV8301 PWM not working

Hi Phil, Thank you for enlightening me about this mode. I'll try this out and report results here. Thank you again!!

View Article


Image may be NSFW.
Clik here to view.

RE: DRV8305: Some problem while driving BLDC motor using DRV8305 and...

Thank you. Below are some problems which I face while doing experiment with Motor.1.  In REVERSE (clockwise) direction It works fine (Very less amount of jerk in a motor) but when I load motor through...

View Article

RE: DRV8432: Vreg=0.48v

Hi Mak, With the inputs configured as stated, the outputs should be disabled. Have you measured resistances between PVDD, GVDD, VDD, VREG, BST_x and GND? Is it possible to slowly raise the voltage on...

View Article


DRV8432: Vreg=0.48v

Part Number: DRV8432I am using DRV8432 first time for a motor control application.Gvdd=vdd=12v,Pvdd=12v.I am working in 1PFB mode.M0=0,M1=Vreg,M3=0.RESET_CD=0v.Reset_AB=NC.PWM_B and PWM_B=0.After power...

View Article

Image may be NSFW.
Clik here to view.

RE: DRV8305: Some problem while driving BLDC motor using DRV8305 and...

Hi Dinesh,It is difficult to determine what is occurring without the hall inputs and the other phase.Please focus on the circled area if possible. It appears there may be a missing commutation...

View Article


RE: DRV8303: DRV8303 Flow Through Drive of High and Low Side FETs

Hi Steve, I apologize for the delay in response and appreciate your patience. 1.) Have you tried increasing the DTC resistor value in your design? I saw that you said you've tried increasing deadtime,...

View Article

RE: DRV8303: DRV8303 Flow Through Drive of High and Low Side FETs

Phil,1) The DTC resistor (pin 3) is the value that I increased. As it was increased, the flow through spike moved with the increased time.2) I tried pull down resistors down to 250 ohms, with no...

View Article

RE: BOOSTXL-ULN2003: Selection of BoosterPack and LaunchPad for Stepper Motor

Hello Andres,Unfortunately, I don't believe that either of the boosterpacks that you mentioned will work for your application.The BOOSTXL-ULN2003 is meant for simple, relatively low current (500mA max)...

View Article
Browsing all 21906 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>